Upgrading Automation Config

You can upgrade Automation Config to the latest stable version from a previous version.

Best practices when upgrading

Follow these guidelines while planning your upgrade:

Do not upgrade using the installer or manual installation instructions.If you are upgrading your Automation Config installation, refer to the following upgrade instructions.
For best results, increment from one major release to the next. As a best practice, always upgrade from the latest major version of Automation Config to the new release. If you are on an older release, upgrade incrementally from one release to the next.
Back up your data. In order to prevent data loss, back up your data.
Perform upgrades during hours of slow network activity. Database upgrades require re-indexing data. Depending on the complexity of your data, a database upgrade could potentially take several hours. To prevent service disruptions, consider upgrading the database during slower business hours or trimming your database prior to an upgrade.
Check the database for any old commands being stored. In some cases, the PostgreSQL database stores old commands that haven’t run. These commands might run during the upgrade process, when you restart the Master Plugin. To prevent this from happening, check whether any old commands are stored in the database, and enable skipping jobs that are older than a defined time.
Test the upgrade before deploying. If possible, you could try running a dress rehearsal in a test environment to get a sense of how long the upgrade could take.
Read through the whole guide first. Consider also reading through this entire guide one time before you implement an upgrade so that you have a good sense of the tasks that are required and whether they require planning from your team or if stakeholders must be notified of pending changes.

Upgrading from older versions

As a best practice, always upgrade from the latest major version of Automation Config to the new release. If you are upgrading from a version earlier than the latest release, you might see the best results if you upgrade in increments from one major release to the next.

For instructions on upgrading to earlier Automation Config versions, see the specific upgrade instructions for the releases you are upgrading from. The upgrade instructions for previous releases are included in the installation guide PDF for the subsequent release. For example, if you need to upgrade from 5.5 to 6.0, see the upgrade instructions in the 6.0 installation PDF.

For Automation Config versions 8.4 and later, use the version selector at the top of this page to select the correct upgrade guide for your product version. For versions 8.3 and older, use the PDF guides in the following table:


Version	Installation and upgrade guide (PDF)
8.3	8.3 Installation and upgrade guide
6.4	6.4 Installation and upgrade guide
6.3	6.3 Installation and upgrade guide
6.2	6.2 Installation and upgrade guide
6.1	6.1 Installation and upgrade guide
6.0.1	6.0.1 Installation and upgrade guide
6.0	6.0 Installation and upgrade guide

How to upgrade Automation Config

To upgrade Automation Config, complete the following tasks in this order:

Back up your data, including certain files and directories that are crucial to your specific installation of Automation Config
Upgrade PostgreSQL (optional, but recommended)
Upgrade your Salt infrastructure (optional, but recommended)
Download the upgrade files
Upgrade the RaaS node
Upgrade any Salt masters using the Master Plugin

For more information on upgrading Config via Aria Suite Lifecycle, see Upgrade Automation Config in the LCM documentation.

Back up Automation Config files and directories

The following files and directories contain your custom Automation Config configurations and need to be backed up before upgrading:

On the RaaS node, back up these entire directories:
- /etc/raas/raas
- /etc/raas/raas.secconf
- /var/log/raas
- /etc/raas/pki/
Note:
The pki directory contains hidden files, so ensure you back up the entire directory.Backing up the log files in the /var/log/raas directory is optional. During the upgrade process, you’ll clear the log files to provide a clean log file if troubleshooting is necessary.
On each Salt master, back up the /etc/salt/master.d/raas.conf and /etc/salt/master.d/eAPIMasterPaths.conf files.
Note:
Depending on how you initially installed Automation Config, the eAPI Salt master paths could instead be in the /etc/salt/master.d/raas.conf file instead.

Back up your database schema

When upgrading your RaaS node, the database schema is updated. For that reason, ensure you create a backup of your database before the upgrade.

To back up your database you need to first look up your PostgreSQL database name and then copy the contents:

On the PostgreSQL server, back up these files:
- postgresql.conf
- pg_hba.conf
Log in as the postgres user using the following command:
```
sudo su - postgres
```
Get your database name, using the following commands to enter PostgreSQL and then list the databases:
```
psql
\l
```
To exit PostgreSQL and log out as the postgres user, press Ctrl+D and then run the following command:
```
exit
```

Copy database contents to a file. The following command gives an example:

pg_dump -U salteapi raas_db_name > postgres_raas_backup_$(date +%Y-%m-%d).sql

Upgrade PostgreSQL database

Automation Config requires a PostgreSQL 9.6 database, but PostgreSQL 13.7 is recommended. The recommended version of PostgreSQL is included with the Automation Config installer.

Upgrading to the latest version of PostgreSQL is not required. However, upgrading PostgreSQL can possibly improve performance. For instructions on upgrading to the latest version of PostgreSQL, see PostgreSQL upgrade.

Upgrade Redis database

Automation Config requires a Redis 5.x database, but Redis 6.2.7 is recommended. The recommended version of Redis is included with the Automation Config installer.

Upgrading to the latest version of Redis 5.x is not required. However, upgrading Redis can possibly improve performance. For instructions on upgrading Redis, see Redis Administration.

Upgrade Salt

When upgrading Salt, you must upgrade the masters first. Running minions with versions of Salt newer than their masters might not function as expected since the minion may include changes not yet available in the master. Also, whenever possible, backward compatibility between new masters and old minions is preserved. Generally, the only exception to this policy is in case of a security vulnerability.

For best performance, ensure that all the Salt components in your infrastructure are running on the latest major version of Salt.

Beginning with the release of Salt 3006, the Salt Project uses the onedir packaging system. Onedir stands for "one directory" as it contains all the executables that Salt needs, including Python and other Salt dependencies. Onedir allows you to use Salt out of the box.

Important: The Salt Project strongly recommends upgrading to onedir to continue receiving Salt version updates. As of Salt version 3006, only onedir packages will be available for upgrades. For more information on Salt versions and onedir, see KB 89728.

Important: Salt versions 3006 and later use a onedir installation package that is not supported or compatible with Automation Config. To use Salt version 3006 or later with Automation Config, use only classic installer packages.

For information on installing onedir packages of Salt, see Install onedir packages of Salt.

Note: The use of the Salt Crystal installer package has been retired, for future installations it is recommended to use the onedir installer package.

Required:For brownfield/upgrade deployments, starting with Salt 3006, the Salt Master is configured to run as user "salt" instead of the traditional "root user". As a result, this can cause permission errors with RaaS related workflows, such as minion deployment and RaaS Master plugin upgrades.

To remedy this, modify the /etc/salt/master.d/raas.conf file to change the user to root: user: root.

For new greenfield deployments, the sseapi-config command configures the master plugin and generates the raas.conf file with the correct user: root config value. No user action is required.

Upgrade the RaaS node

After upgrading to the latest version of PostgreSQL, Redis, and Salt, you can then upgrade the RaaS node from the previous version to the latest version.

Note: Database upgrades require re-indexing data. If your data is complex, a database upgrade might take several hours.

Important:

Before upgrading your RaaS node, you must back up your system data to avoid data loss. To preserve your setup, save any changes you made to the default file system, pillar data, and jobs as new files or jobs. Additionally, you should record or make a copy of any existing pillar target assignments, as these are removed during the upgrade process.

To upgrade the RaaS node:

Download the upgrade files from Customer Connect.
Stop the RaaS service using the following command:
```
sudo systemctl stop raas
```
Remove the log file(s) in the /var/log/raas directory. Clearing the log files provides a clean log file if troubleshooting is necessary.
Remove the currently installed version of the API (RaaS) with the following command:
```
sudo yum remove raas
```
Upgrade the RaaS node by installing the latest RPM. Use the following example command, replacing the exact file name of the RPM:
```
sudo yum install raas-rpm-file-name.rpm
```
IMPORTANT: Restore the backup of the following files:
- /etc/raas/raas
- /etc/raas/raas.secconf
- /etc/raas/pki/
Update permissions for the raas user with the following command:
```
sudo chown -R raas:raas /etc/pki/raas/certs
```
OPTIONAL: If you have a Automation for Secure Hosts license and want to add the compliance library, add the following new section to the /etc/raas/raas file:
```
sec:
  ingest_override: true
  locke_dir: locke
  post_ingest_cleanup: true
  username: 'secops'
  content_url: 'https://enterprise.saltstack.com/secops_downloads'
  download_enabled: true
  download_frequency: 86400
  stats_snapshot_interval: 3600
  compile_stats_interval: 10
  ingest_on_boot: True
  content_lock_timeout: 60
  content_lock_block_timeout: 120
```
Note:
This step is optional and only applies to organizations that have a valid Automation for Secure Hosts license. This add-on module is available for Automation Config versions 6.0 and later. The previous configuration options in the /etc/raas/raas configuration file are specific to these add-on modules.

OPTIONAL: If you have a Automation for Secure Hosts license and want to add the vulnerability library, add a new section to the /etc/raas/raas file:

vman:
  vman_dir: vman
  download_enabled: true
  download_frequency: 86400
  username: vman
  content_url: 'https://enterprise.saltstack.com/vman_downloads'
  ingest_on_boot: true
  compile_stats_interval: 60
  stats_snapshot_interval: 3600
  old_policy_file_lifespan: 2
  delete_old_policy_files_interval: 86400
  tenable_asset_import_enabled: True
  tenable_asset_import_grains: ['fqdn', 'ipv4', 'ipv6', 'hostname', 'mac_address', 'netbios_name',
                                'bios_uuid', 'manufacturer_tpm_id', 'ssh_fingerprint',
                                'mcafee_epo_guid', 'mcafee_epo_agent_guid', 'symantec_ep_hardware_key',
                                'qualys_asset_id', 'qualys_host_id', 'servicenow_sys_id', 'gcp_project_id',
                                'gcp_zone', 'gcp_instance_id', 'azure_vm_id', 'azure_resource_id',
                                'aws_availability_zone', 'aws_ec2_instance_ami_id',
                                'aws_ec2_instance_group_name', 'aws_ec2_instance_state_name',
                                'aws_ec2_instance_type', 'aws_ec2_name', 'aws_ec2_product_code',
                                'aws_owner_id', 'aws_region', 'aws_subnet_id', 'aws_vpc_id',
                                'installed_software', 'bigfix_asset_id'
                                ]

Note:

This step is optional and only applies to organizations that have a valid Automation for Secure Hosts license. This add-on module is available for Automation Config versions 6.0 and later. The previous configuration options in the /etc/raas/raas configuration file are specific to these add-on modules.

The RaaS currently has a known issue related to stale jobs. When upgrading, some users might notice a queue of stale jobs that are stuck in a pending state. Upgrading the RaaS node can cause these jobs to run unless they are first cleared out.
To prevent this from happening, first check whether any old commands are stored in the database. On your PostgreSQL node, check for any pending jobs using the following command:
```
select count(1) from commands where state='new';
```
The result is the number of pending jobs. If the number of jobs is 0, proceed with the rest of the upgrade process.
Upgrade the RaaS service database using the following command:
```
sudo su - raas
raas upgrade
```
Note:
Depending on the size of your database, the upgrade can take anywhere from several minutes to over an hour. If you encounter errors, check the /var/log/raas/raas log file for more information.
After the upgrade, exit the session for the raas user with the following command:
```
exit
```

Start the RaaS service using the following command:

sudo systemctl enable raas
sudo systemctl start raas

Upgrade the Master Plugin Using the Automation Config User Interface

Note: This feature is supported for Automation Config versions 8.11.2 or later. For earlier versions, you must first upgrade your master plugin to version 8.11.2 or later using the CLI.

Note: The Salt master must be run as root.

Automation Config automatically upgrades the master plugin to the latest version without any actions required by the user.

However, you can also upgrade the master plugin from the Automation Config user interface. To upgrade the master plugin, from Automation Config, select Administration and then click Master Plugins. The Master Plugin tab shows you which version of the plugin and Automation Config environment you are on, along with a list of your Master Plugin IDs. From the Master Plugins tab, you can select the master plugins you want to update and then click Update.

Upgrade the Master Plugin Using the CLI

After you have successfully upgraded the RaaS node, you can then upgrade any Salt masters that use the Master Plugin to connect to Automation Config.

It is recommended to update your Master Plugin configuration by generating a default config file and applying any settings you to preserve from your existing configuration. For example:

# sseapi-config --default >/tmp/raas.conf 
# cd /etc/salt/master.d 
# vim -d raas.conf /tmp/raas.conf

Important: If you installed Salt using onedir, the path to this executable is /opt/saltstack/salt/extras-3.10/bin/sseapi-config.

Starting with the 8.13.0 release, the Master Plugin includes a tgtmatch engine that now offloads target group matching from the RaaS server to the Salt Masters. It is recommended to enable and configure that tgtmatch engine to make target group matching more responsive, especially in environments with:

A large number of target groups (100 or more)
A large number of minions (3000 or more)
Frequent changes to minion grains (daily or more frequent)
Frequent creation and deletion of minions (daily or more frequent)

To configure the tgtmatch engine, ensure that these settings are present in the Master Plugin config file (/etc/salt/master.d/raas.conf)

engines: 
    - sseapi: {} 
    - eventqueue: {} 
    - rpcqueue: {} 
    - jobcompletion: {}    
    - tgtmatch: {} 

sseapi_local_cache:     
    load: 3600 
    tgt: 86400 
    pillar: 3600 
    exprmatch: 86400 
    tgtmatch: 86400 

sseapi_tgt_match: 
    poll_interval: 60     
    workers: 0 
    nice: 19

To configure RaaS to expect target matching data to be supplied by the Salt Masters, ensure that the following setting is present in the RaaS Config file (/etc/raas/raas):

target_groups_from_master_only: true

Note:

Before you upgrade the Salt master(s), ensure that the pip3 application is installed on the Salt masters. If you are upgrading from the latest version of the Master Plugin, then this application is already installed.

To upgrade the Master Plugin on a Salt master:

Stop the salt-master service using the following command:
```
sudo systemctl stop salt-master
```
Check which version of Python is running on the Salt master. If it is running Python 3.6 or higher, no changes are needed. Otherwise, delete the prior version of the SSEAPE module. (The SSEAPE is the Automation Config plugin for the Salt master). For example:
RHEL/CentOS
```
sudo rm -rf /usr/lib/python3.6/site-packages/SSEAPE*
```
Ubuntu
```
sudo rm /usr/lib/python3.6/dist-packages/SSEAPE*
```
Upgrade the Master Plugin by manually uninstalling and reinstalling the updated Python wheel. Use the following example commands, replacing the exact name of the wheel file:
Note: The existing plugin must be uninstalled to prevent multiple instances of sseapi-config.
```
pip3 uninstall SSEAPE-8.12.1.3-py3-none-any.whl
mv /etc/salt/master.d/raas.conf /tmp
salt-call pip.install SSEAPE-8.12.1.3-py3-none-any.whl
cp /tmp/raas.conf /etc/salt/master.d/raas.conf
systemctl restart salt-master
```
Update the API (RaaS) module paths by editing the /etc/salt/master.d/eAPIMasterPaths.conf file to reference the paths to the various modules. For example, you might change all python2.7 references in this file to python3.6.
Note:
Depending on how you initially installed Automation Config, the eAPI Salt master paths could instead be in the /etc/salt/master.d/raas.conf file instead.
Check the engines section in /etc/salt/master.d/raas.conf to confirm that it matches the following:
```
engines:
  - sseapi: {}
  - eventqueue: {}
  - rpcqueue: {}
  - jobcompletion: {}
```
Note:
If a problem occurred, you may need to restore your backups of the /etc/salt/master.d/raas.conf and /etc/salt/master.d/eAPIMasterPaths.conf files.
If you are using the salt-master key authentication (recommended), make sure that sseapi_username and sseapi_password are commented out in /etc/salt/master.d/raas.conf.
```
#sseapi_username:
#sseapi_password:
```
Check that the master_job_cache and event_return entries are set to sseapi. The pgjsonb returner is no longer available.
Start the salt-master service with the following command:
```
sudo systemctl start salt-master
```
Verify that the Salt Master is running as user "root" and not user "salt". If not, modify the /etc/salt/master.d/raas.conf file to change the user to root: user: root.

The upgrade process is now complete. If you encounter any other errors, refer to Troubleshooting.