Download the VMware Aria Operations for Logs virtual appliance. VMware distributes the VMware Aria Operations for Logs virtual appliance as an .ova file. Deploy the VMware Aria Operations for Logs virtual appliance by using the vSphere Client.
Prerequisites
- Verify that you have a copy of the VMware Aria Operations for Logs virtual appliance .ova file.
- Verify that you have permissions to deploy OVF templates to the inventory.
- Verify that your environment has enough resources to accommodate the minimum requirements of the VMware Aria Operations for Logs virtual appliance. See Minimum Requirements.
- Verify that you have read and understand the virtual appliance sizing recommendations. See Sizing the Virtual Appliance.
Procedure
- In the vSphere Client, select .
- Follow the prompts in the Deploy OVF Template wizard.
- On the Select Configuration page, select the size of the VMware Aria Operations for Logs virtual appliance based on the size of the environment for which you intend to collect logs.
Small is the minimum requirement for production environments.
VMware Aria Operations for Logs provides preset VM (virtual machine) sizes that you can select from to meet the ingestion requirements of your environment. These presets are certified size combinations of compute and disk resources, though you can add extra resources afterward. A small configuration consumes the fewest resources while remaining supported. An extra small configuration is suitable only for demos.
Preset Size |
Log Ingest Rate |
Virtual CPUs |
Memory |
IOPS |
Syslog Connections (Active TCP Connections) |
Events per Second |
Extra Small |
6 GB/day |
2 |
4 GB |
75 |
20 |
400 |
Small |
30 GB/day |
4 |
8 GB |
500 |
100 |
2000 |
Medium |
75 GB/day |
8 |
16 GB |
1000 |
250 |
5000 |
Large |
225 GB/day |
16 |
32 GB |
1500 |
750 |
15,000 |
You can use a syslog aggregator to increase the number of syslog connections that send events to
VMware Aria Operations for Logs. However, the maximum number of events per second is fixed and does not depend on the use of a syslog aggregator. A
VMware Aria Operations for Logs instance cannot be used as a syslog aggregator.
Note: If you select
Large, you must upgrade the virtual hardware on the
VMware Aria Operations for Logs virtual machine after the deployment.
- On the Select Storage page, select a disk format.
Note: Shrinking disks on the
VMware Aria Operations for Logs virtual appliance is not supported and might result in data corruption or data loss.
- (Optional) On the Select Networks page, set the networking parameters for the VMware Aria Operations for Logs virtual appliance. You can select the IPv4 or IPv6 protocol.
If you do not provide network settings, such as an IP address, DNS servers, and gateway information,
VMware Aria Operations for Logs uses DHCP to set those settings.
Caution: Do not specify more than two domain name servers. If you specify more than two domain name servers, all configured domain name servers are ignored in the
VMware Aria Operations for Logs virtual appliance.
Use a comma-separated list to specify domain name servers.
- (Optional) On the Customize template page, set network properties if you are not using DHCP.
Under Application, select the
Prefer IPv6 addresses check box if you want to run the virtual machine in a dual stack network.
Caution: Do not select the
Prefer IPv6 addresses check box if you want to use pure IPv4 even with IPv6 supported in your network. Select the check box only if your network has a dual stack or pure stack support for IPv6.
- (Optional) On the Customize template page, select Other Properties and set the root password for the VMware Aria Operations for Logs virtual appliance.
The root password is required for SSH. You can also set this password through the VMware Remote Console.
- Follow the prompts to complete the deployment.
For information on deploying virtual appliances, see the VMware Aria Operations vApps Deployment and Configuration guide.
After you power on the virtual appliance, an initialization process begins. The initialization process takes several minutes to complete. At the end of the process, the virtual appliance restarts.
- Navigate to the Console tab and verify the IP address of the VMware Aria Operations for Logs virtual appliance.
IP Address Prefix |
Description |
https:// |
The DHCP configuration on the virtual appliance is correct. |
http:// |
The DHCP configuration on the virtual appliance failed.
- Power off the VMware Aria Operations for Logs virtual appliance.
- Right-click the virtual appliance and select Edit Settings.
- Set a static IP address for the virtual appliance.
|