You can install NSX Edge VMs in a manual fashion using an ISO file.

Important: The NSX-T Data Center component virtual machine installations include VMware Tools. Removal or upgrade of VMware Tools is not supported for NSX-T Data Center appliances.

Prerequisites

Procedure

  1. Go to your MyVMware account (myvmware.com) and navigate to VMware NSX-T Data Center > Downloads.
  2. Locate and download the ISO file for NSX Edge.
  3. In the vSphere Client, select the host datastore.
  4. Select Files > Upload Files > Upload a File to a Datastore, browse to the ISO file, and upload.
    If you are using a self-signed certificate, open the IP address in a browser and accept the certificate and reupload the ISO file.
  5. In the vSphere Client inventory, select the host you uploaded the ISO file. or in the vSphere Client,
  6. Right-click and select New Virtual Machine .
  7. Select a compute resource for the NSX Edge appliance.
  8. Select a datastore to store the NSX Edge appliance files.
  9. Accept the default compatibility for your NSX Edge VM.
  10. Select the supported ESXi operating systems for your NSX Edge VM.
  11. Configure the virtual hardware.
    • New Hard Disk - 200 GB
    • New Network - VM Network
    • New CD/DVD Drive - Datastore ISO File

      You must click Connect to bind the NSX Edge ISO file to the VM.

  12. Power on the new NSX Edge VM.
  13. During ISO boot, open the VM console and choose Automated installation.
    There might be a pause of 10 seconds after you press Enter.

    During installation, the installer prompts you to enter a VLAN ID for the management interface. Select Yes and enter a VLAN ID to create a VLAN subinterface for the network interface. Select No if you do not want to configure VLAN tagging on the packet.

    During power-on, the VM requests a network configuration via DHCP. If DHCP is not available in your environment, the installer prompts you for IP settings.

    By default, the root login password is vmware, and the admin login password is default.

    When you log in for the first time, you are prompted to change the password. This password change method has strict complexity rules, including the following:
    • At least 12 characters
    • At least one lower-case letter
    • At least one upper-case letter
    • At least one digit
    • At least one special character
    • At least five different characters
    • No dictionary words
    • No palindromes
    • More than four monotonic character sequence is not allowed
    Important: The core services on the appliance do not start until a password with sufficient complexity has been set.
  14. For an optimal performance, reserve memory for the NSX Edge appliance.

    Set the reservation to ensure that NSX Edge has sufficient memory to run efficiently. See NSX Edge VM System Requirements.

  15. After the NSX Edge starts, log in to the CLI with admin credentials.
    Note: After NSX Edge starts, if you do not log in with admin credentials for the first time, the data plane service does not automatically start on NSX Edge.
  16. There are three ways to configure a management interface.
    • Untagged interface. This interface type creates an out-of-band management interface.

      (DHCP) set interface eth0 dhcp plane mgmt

      (Static) set interface eth0 ip <CIDR> gateway <gateway-ip> plane mgmt

    • Tagged interface.

      set interface eth0 vlan <vlan_ID> plane mgmt

      (DHCP) set interface eth0.<vlan_ID> dhcp plane mgmt

      (Static) set interface eth0.<vlan_ID> ip <CIDR> gateway <gateway-ip> plane mgmt

    • In-band interface.

      set interface mac <mac_address> vlan <vlan_ID> in-band plane mgmt

      (DHCP) set interface eth0.<vlan_ID> dhcp plane mgmt

      (Static) set interface eth0.<vlan_ID> ip <CIDR> gateway <gateway-ip> plane mgmt

  17. (Optional) Start SSH service. Run start service ssh .
  18. Run the get interface eth0.<vlan_ID> command to verify that the IP address was applied as expected
    nsx-edge-1> get interface eth0.100 
    
    Interface: eth0.100
      Address: 192.168.110.37/24
      MAC address: 00:50:56:86:62:4d
      MTU: 1500
      Default gateway: 192.168.110.1
      Broadcast address: 192.168.110.255
      ...
    
    Note: When bringing up NSX Edge VMs on non-NSX managed host, verify that the MTU setting is set to 1600 (instead of 1500) on the physical host switch for the data NIC.
  19. (Tagged interface and In-band interface) Any existing VLAN management interface must be cleared before creating a new one.

    Clear interface eth0.<vlan_ID>

    To set a new interface, refer to step 15.

  20. Verify that the NSX Edge appliance has the required connectivity.

    If you enabled SSH, make sure that you can SSH to your NSX Edge.

    • You can ping your NSX Edge.
    • NSX Edge can ping its default gateway.
    • NSX Edge can ping the hypervisor hosts that are in the same network as the NSX Edge.
    • NSX Edge can ping its DNS server and its NTP server.
  21. Troubleshoot connectivity problems.
    Note: If connectivity is not established, make sure the VM network adapter is in the proper network or VLAN.

    By default, the NSX Edge datapath claims all virtual machine NICs except the management NIC (the one that has an IP address and a default route). If you incorrectly assigned a NIC as the management interface, follow these steps to use DHCP to assign management IP address to the correct NIC.

    1. Log in CLI and type the stop service dataplane command.
    2. Type the set interface interface dhcp plane mgmt command.
    3. Place interface into the DHCP network and wait for an IP address to be assigned to that interface.
    4. Type the start service dataplane command.
      The datapath fp-ethX ports used for the VLAN uplink and the tunnel overlay are shown in the get interfaces and get physical-port commands on the NSX Edge.

What to do next

If you did not join the NSX Edge with the management plane, see Join NSX Edge with the Management Plane.