Add an Autonomous Edge as an L2 VPN Client

You can use L2 VPN to extend your Layer 2 networks to a site that is not managed by NSX-T Data Center. An autonomous NSX Edge can be deployed on the site, as an L2 VPN client. The autonomous NSX Edge is simple to deploy, easily programmable, and provides high-performance VPN. The autonomous NSX Edge is deployed using an OVF file on a host that is not managed by NSX-T Data Center. You can also enable high availability (HA) for VPN redundancy by deploying primary and secondary autonomous Edge L2 VPN clients.

Prerequisites

• Create a port group and bind it to the vSwitch on your host. Ensure that this port group accepts promiscuous mode and forged transmits from the port group's security settings.
• Create a port group for your internal L2 extension port.
• Obtain the IP addresses for the local IP and remote IP to use with the L2 VPN Client session you are adding.
• Obtain the peer code that was generated during the L2 VPN server configuration.

Procedure

1. Using vSphere Web Client, log in to the vCenter Server that manages the non-NSX environment.
2. Select Hosts and Clusters and expand clusters to show the available hosts.
3. Right-click the host where you want to install the autonomous NSX Edge and select Deploy OVF Template.
4. Enter the URL to download and install the OVF file from the Internet or click Browse to locate the folder on your computer that contains the autonomous NSX Edge OVF file and click Next.
5. On the Select name and folder page, enter a name for the autonomous NSX Edge and select the folder or data center where you want to deploy. Then click Next.
6. On the Select a compute resource page, select the destination of the compute resource.
7. On the OVF Template Details page, review the template details and click Next.
8. On the Configuration page, select a deployment configuration option.
9. On the Select storage page, select the location to store the files for the configuration and disk files.
10. On the Select networks page, configure the networks that the deployed template must use. Select the port group you created for the uplink interface, the port group that you created for the L2 extension port, and enter an HA interface. Click Next.
11. On the Customize Template page, enter the following values and click Next.
    1. Type and retype the CLI admin password.
    2. Type and retype the CLI enable password.
    3. Type and retype the CLI root password.
    4. Enter the IPv4 address for the Management Network.
    5. Enable the option to deploy an autonomous Edge.
    6. Enter the External Port details for VLAN ID, exit interface, IP address, and IP prefix length such that the exit interface maps to the Network with the port group of your uplink interface.

       If the exit interface is connected to a trunk port group, specify a VLAN ID. For example, 20,eth2,192.168.5.1,24. You can also configure your port group with a VLAN ID and use VLAN 0 for the External Port.

    7. (Optional) To configure High Availability, enter the HA Port details where the exit interface maps to the appropriate HA Network.
    8. (Optional) When deploying an autonomous NSX Edge as a secondary node for HA, select Deploy this autonomous-edge as a secondary node.

       Use the same OVF file as the primary node and enter the primary node's IP address, user name, password, and thumbprint.

       To retrieve the thumbprint of the primary node, log in to the primary node and run the following command:

        get certificate api thumbprint

       Ensure that the VTEP IP addresses of the primary and secondary nodes are in the same subnet and that they connect to the same port group. When you complete the deployment and start the secondary-edge, it connects to the primary node to form an edge-cluster .

12. On the Ready to complete page, review the autonomous Edge settings and click Finish.
    Note: If there are errors during the deployment, a message of the day is displayed on the CLI. You can also use an API call to check for errors:

    GET https://<nsx-mgr>/api/v1/node/status

    The errors are categorized as soft errors and hard errors. Use API calls to resolve the soft errors as required. You can clear the message of day using an API call:

    POST /api/v1/node/status?action=clear_bootup_error

13. Power on the autonomous NSX Edge appliance.
14. Log in to the autonomous NSX Edge client.
15. Select L2VPN > Add Session and enter the following values:
    1. Enter a session name.
    2. Enter the local IP address and the remote IP address.
    3. Enter the peer code from the L2VPN server. See Download the Remote Side L2 VPN Configuration File for details on obtaining the peer code.
16. Click Save.
17. Select Port > Add Port to create an L2 extension port.
18. Enter a name, a VLAN, and select an exit interface.
19. Click Save.
20. Select L2VPN > Attach Port and enter the following values:
    1. Select the L2 VPN session that you created.
    2. Select the L2 extension port that you created.
    3. Enter a tunnel ID.
21. Click Attach.
    You can create additional L2 extension ports and attach them to the session if you need to extend multiple L2 networks.
22. Use the browser to log in to the autonomous NSX Edge or use API calls to view the status of the L2VPN session.
    Note: If the L2VPN server configuration changes, ensure that you download the peer code again and update the session with the new peer code.