The table explains system event messages for NSX Edge of major, critical, or high severity. System events with informational severity are listed if such events triggers the alarm.

Event Code

Event Severity

Alarm Code

Event Message

Description

30011

High

N/A

None of the NSX Edge VMs found in serving state. There is a possibility of network disruption.

The NSX Edge VMs should recover automatically from this state. Check for a trap with event code 30202 or 30203.

Action: See "Edge Appliance Troubleshooting" in the NSX Troubleshooting Guide.

30013

Critical

130013

NSX Manager found NSX Edge VM (vmId : {#}) in bad state. Needs a force sync.

NSX Edge VM is reporting a bad state, and might not be functioning correctly.

Action: An automatic force sync is triggered when a problematic state is detected. If the automatic force sync fails, try a manual force sync.

30014

Major

N/A

Failed to communicate with the NSX Edge VM.

The NSX Manager communicates with NSX Edge through the VIX or Message Bus. The communication channel is selected by the NSX Manager on the basis of whether host preparation is done or not at the time of edge deployment or re-deployment. This event indicates that NSX Manager lost communication with the NSX Edge.

Action: See "Edge Appliance Troubleshooting" in the NSX Troubleshooting Guide.

30027

Informational

130027

NSX Edge VM (vmId : {#}) is powered off.

The NSX Edge VM was powered off.

Action: Information-only event.

30032

High

130032

NSX Edge appliance with vmId : {#} not found in the vCenter inventory.

The NSX Edge VM was likely deleted directly from vCenter Server. This is not a supported operation as NSX-managed objects must be added or deleted from the vSphere Web Client interface for NSX.

Action: Redeploy the edge or deploy a new edge.

30033

High

130033

NSX Edge VM (vmId : {#}) not found in the vCenter inventory.

The NSX Edge VM cannot be found in the vCenter inventory.

Action: Check whether the VM was deleted accidentally. If confirmed, redeploy the edge.

30034

Critical

130034

None of the NSX Edge VMs found in serving state. There is a possibility of network disruption.

The Edge VM is not responding to the health check sent by the NSX Manager.

Action: Confirm the edge VM is powered on. Then collect the edge logs and contact VMware technical support.

30037

Critical

N/A

Edge firewall rule modified as {#} is no longer available for {#}.

An invalid GroupingObject (IPSet, securityGroup, and so on) is present in the firewall rule.

Action: Revisit the firewall rule and make required updates.

30038

Critical

N/A

Powered-on NSX Edge appliance : {EdgeId #}, {vmName #} violates the virtual machine anti-affinity rule.

NSX Edge High Availability applies anti-affinity rules to vSphere hosts automatically so that the active and standby edge VMs are deployed on different hosts. This event indicates that these anti-affinity rules were removed from the cluster and that both edge VMs are running on the same host.

Action: Go to vCenter Server, and verify the anti-affinity rules.

30045

Critical

N/A

NSX Edge VM health check failing with critical vix errors. Further health check is disabled for vm. Please redeploy or forcesync vm to resume health check.

The network environment might be causing repeated communication failures to the edge VM over the VIX channel.

Action: Collect the NSX Manager and NSX Edge technical support logs if NSX Edge is responsive. Then do a force sync. If the problem persists, redeploy NSX Edge(See "Redeploy NSX Edge" in the NSX Administration Guide).

Note:

Redeploying is a disruptive action. It is recommended that you first do a force sync and if the issue is not resolved, then deploy again.

30046

Critical

N/A

Pre rules publish failed on edge: {EdgeID#}, vm: {#} for generation number {#}. Refer logs for detail. It may need forcesync.

The NSX Edge firewall rules might be out of sync. This error is generated if the pre rules (configured from DFW UI/API) fails.

Action: If the problem is not resolved automatically by the built-in recovery process, do a manual force sync.

30100

Critical

N/A

NSX Edge was force synced.

The NSX Edge VM was force synced.

Action: If the force sync does not resolve the problem, collect the technical support logs for NSX Manager and NSX Edge, and contact VMware technical support.

30102

High

130102

NSX Edge (vmId : {IP Address}) is in Bad State. Needs a force sync.

The NSX Edge VM is experiencing an internal error.

Action: If the problem is not resolved automatically by the built-in recovery process, try a manual force sync.

30148

Critical

N/A

NSX Edge CPU usage has increased. {#} Top processes are: {#}.

The NSX Edge VM CPU utilization is high for sustained periods.

Action: Refer to "Edge Appliance Troubleshooting" in the NSX Troubleshooting Guide. If the problem persists, collect the technical support logs for NSX Manager and NSX Edge, and contact VMware technical support.

30153

Major

N/A

AESNI crypto engine is up.

AESNI crypto engine is up.

Action: None required.

30154

Major

N/A

AESNI crypto engine is down.

AESNI crypto engine is down.

Action: None required. This status is expected.

30155

High

130155

Insufficient CPU and/or Memory Resources available on Host or Resource Pool, during resource reservation at the time of NSX Edge deployment.

Insufficient CPU and/or memory resources on host or resource pool.

You can view the available resources and reserved resources by navigating to the Home > Hosts and Clusters > [Cluster-name]> Monitor > Resource Reservationpage.

After checking the available resources, specify the resources as part of appliance configuration again, so that resource reservation limit succeeds.

30180

Critical

N/A

NSX Edge is out of memory. The Edge is rebooting in 3 seconds. Top 5 processes are: {#}.

The NSX Edge VM has run out of memory. A reboot was initiated to recover.

Action: Refer to "Edge Appliance Troubleshooting" in the NSX Troubleshooting Guide. If the problem persists, collect the technical support logs for NSX Manager and NSX Edge, and contact VMware technical support.

30181

Critical

130181

NSX Edge {EdgeID#} VM name {#} file system is read only.

There is connectivity issue with the storage device backing the NSX Edge VM.

Action: Check and correct any connectivity issue with the backing datastore. You might need to execute a manual force sync after the connectivity issue is resolved.

30202

Major

N/A

NSX Edge {EdgeID#} HighAvailability switch over happened. VM {#} name {#} has moved to ACTIVE state.

An HA failover has occurred, and the secondary NSX Edge VM has transitioned from the STANDBY to ACTIVE state.

Action: No action is required.

30203

Major

N/A

NSX Edge {EdgeID} HighAvailability switch over happened. VM {#} name {#} has moved to STANDBY state.

An HA failover occurred, and the primary NSX Edge VM transitioned from the ACTIVE to STANDBY state.

Action: No action is required.

30205

Critical

130205

Split Brain detected for NSX Edge {EdgeID} with HighAvailability.

Due to network failure, NSX Edge VM's configured for HA are unable to determine if the other VM is online. In such scenario, both the VM's think the other is not online and take on the ACTIVE state. This may cause network disruption.

Action : Check network infrastructure (virtual and physical) to look for any failures, specially on the interfaces and the path configured for HA.

30302

Critical

130302

LoadBalancer virtualServer/pool : {virtualServerName]} Protocol : {#} serverIp : {IP Address} changed the state to down.

A virtual server or pool on the NSX Edge load balancer is down.

Action: Refer to the "Load Balancing" section in the NSX Troubleshooting Guide.

30303

Major

N/A

LoadBalancer virtualServer/pool : {0} Protocol : {#} serverIp : {IP Address} changed to a wrong state.

A virtual server or pool on the NSX Edge load balancer is experiencing an internal error.

Action: Refer to the "Load Balancing" section in the NSX Troubleshooting Guide.

30304

Major

130304

LoadBalancer pool : {0} Protocol : {#} serverIp : {IP address} changed to a warning state.

An NSX Edge load balancer pool changed its state to warning.

Action: Refer to the "Load Balancing" section in the NSX Troubleshooting Guide.

30402

Critical

130402

IPsec Channel from localIp : {IP address} to peerIp : {IP address} changed the status to down.

An NSX Edge IPSec VPN channel is down.

Action: Refer to the "Virtual Private Networks (VPN)" section in the NSX Troubleshooting Guide.

30404

Critical

130404

EDGE IPSEC TUNNEL DOWN : IPsec Tunnel from localSubnet : {subnet} to peerSubnet : {subnet} changed the status to down.

An NSX Edge IPSec VPN channel is down.

Action: Refer to the "Virtual Private Networks (VPN)" section in the NSX Troubleshooting Guide.

30405

Major

N/A

IPsec Channel from localIp : {IP address} to peerIp : {IP address} changed the status to unknown.

An NSX Edge IPSec VPN channel's status cannot be determined.

Action: Refer to the "Virtual Private Networks (VPN)" section in the NSX Troubleshooting Guide.

30406

Major

N/A

IPsec Channel from localIp : {IP address} to peerIp : {IP address} changed the status to unknown.

An NSX Edge IPSec VPN channel's status cannot be determined.

Action: Refer to the "Virtual Private Networks (VPN)" section in the NSX Troubleshooting Guide.

30701

Critical

N/A

NSX Edge DHCP Relay service on edge {EdgeID} is disabled because there is no external DHCP server provided. Please check server IP or referenced grouping object.

The NSX Edge DHCP Relay service is disabled. Possible reasons: (1) The DHCP Relay process is not running. (2) There is no external DHCP server. This might be caused by the deletion of grouping object referenced by the relay.

Action: See "Configuring DHCP Relay" in the NSX Administration Guide.

30206

Critical

N/A

Resolved Split Brain for NSX Edge {EdgeID} with HighAvailability.

The two NSX Edge HA appliances are able to communicate with each other and have re-negotiated active and standby status.

Action: Refer to "Troubleshooting NSX Edge High Availability (HA) issues: (http://kb.vmware.com/kb/2126560).

30207

Critical

N/A

Attempted Split Brain resolution for NSX Edge {EdgeID} with count {value}.

The two NSX Edge HA appliances are attempting to re-negotiate and recover from a split brain condition.

Note:

: The recovery mechanism reported by this event occurs only in NSX Edge releases earlier than 6.2.3.

Action: Refer to "Troubleshooting NSX Edge High Availability (HA) issues: (http://kb.vmware.com/kb/2126560).