After you save a segment with DHCP configuration, you must be careful about changing the connectivity of the segment.

Segment connectivity changes are allowed only when the segments and gateways belong to the same transport zone.

The following scenarios explain the segment connectivity changes that are allowed or disallowed, and whether DHCP is impacted in each of these scenarios.

Scenario 1: Move a Routed Segment with Gateway DHCP Server to a Different Gateway

Consider that you have added a segment and connected it either to a tier-0 or tier-1 gateway. You configured Gateway DHCP server on this segment, saved the segment, and connected workloads to this segment. DHCP service is now used by the workloads on this segment.

Later, you decide to change the connectivity of this segment to another tier-0 or tier-1 gateway, which is in the same transport zone. This change is allowed. However, when you save the segment, an information message alerts you that changing the gateway connectivity impacts the existing DHCP leases, which are assigned to the workloads.

Scenario 2: Move a Routed Segment with Segment DHCP Server or Relay to a Different Gateway

Consider that you have added a segment and connected it either to a tier-0 or tier-1 gateway. You configured Segment DHCP server or DHCP Relay on this segment, saved the segment, and connected workloads to this segment. DHCP service is now used by the workloads on this segment.

Later, you decide to change the connectivity of this segment to another tier-0 or tier-1 gateway, which is in the same transport zone. This change is allowed. As the DHCP server is local to the segment, the DHCP configuration settings, including ranges, static bindings, and DHCP options are retained on the segment. The DHCP leases of the workloads are retained and there is no loss of network connectivity.

After the segment is moved to a new gateway, you can continue to update the DHCP configuration settings and other segment properties. You can change the DHCP type and DHCP profile of a routed segment after moving the segment to a different gateway.

Scenario 3: Move a Standalone Segment with Segment DHCP Server to a Tier-0 or Tier-1 Gateway

Consider that you have added a segment with None connectivity in your network. You have configured Segment DHCP server on this segment, saved the segment, and connected workloads to this segment. DHCP service is now used by the workloads on this segment.

Later, you decide to connect this segment either to a tier-0 or tier-1 gateway, which is in the same transport zone. This change is allowed. As a Segment DHCP server existed on the segment, the DHCP configuration settings, including ranges, static bindings, and DHCP options are retained on the segment. The DHCP leases of the workloads are retained and there is no loss of network connectivity.

After the segment is connected to the gateway, you can continue to update the DHCP configuration settings, and other segment properties. However, you cannot select a different DHCP type and the DHCP profile in the segment. For example, you cannot change the DHCP type from a Segment DHCP server to a Gateway DHCP server or a DHCP Relay. In addition, you cannot change the DHCP server profile in the segment. But you can edit the properties of the DHCP profile, if needed.

Scenario 4: Move a Standalone Segment Without DHCP Configuration to a Tier-0 or Tier-1 Gateway

Consider that you have added a segment with None connectivity in your network. You have not configured DHCP on this segment, saved the segment, and connected workloads to this segment.

Later, you decide to connect this segment either to a tier-0 or tier-1 gateway, which is in the same transport zone. This change is allowed. As no DHCP configuration existed on the segment, the segment automatically uses the Gateway DHCP server after it is connected to the gateway. The DHCP profile attached to this gateway gets autoselected in the segment.

Now, you can specify the DHCP configuration settings, including ranges, static bindings, and DHCP options on the segment. You can also edit the other segment properties, if necessary. However, you cannot change the DHCP type from a Gateway DHCP server to a Segment DHCP server or a DHCP Relay.

Remember, you can configure only a Gateway DHCPv4 server on the segment. Gateway DHCPv6 server is not supported.

Scenario 5: Move a Segment with Tier-0 or Tier-1 Connectivity to None Connectivity

Consider that you have added a segment to a tier-0 or tier-1 gateway in your network. You have configured Gateway DHCP server or DHCP Relay on this segment, saved the segment, and connected workloads to this segment. DHCP service is now used by the workloads on this segment.

Later, you decide to change the connectivity of this segment to None. This change is not allowed.

In this scenario, the following workaround can help:
  1. Temporarily disconnect the existing segment from the gateway or delete the segment.
    1. Navigate to Networking > Segments.
    2. Click the vertical ellipses next to the segment, and then click Edit.
    3. Turn off the Gateway Connectivity option to disconnect the segment temporarily from the gateway.
  2. Add a new segment and do not connect it to any gateway.
  3. Configure a Segment DHCP server on this standalone segment, if needed.