Migration Modes

There are multiple ways you can migrate NSX-V to NSX.

The following standard migration modes are available:

• NSX for vSphere
  • Fixed Topology

    Fixed-topology migration is limited to the topologies supported in Fixed Topologies Supported for End-to-End Migration.

  • User-defined Topology

    You can migrate any topology as long as some conditions are met (see Define a Topology for details). You create the layer-3 topology on NSX with tier-0 and/or tier-1 gateways and map the NSX-V Edge Services Gateways (ESGs) and Distributed Logical Routers (DLRs) to the NSX tier-0 or tier-1 gateways.

    The following modes are available when you choose user-defined topology:

    • Complete Migration
    • Configuration Migration
    • Configuration and Edge Migration

  The folowing screen shows the migration modes that are available when you select NSX for vSphere:

  

  The folowing screen shows the migration modes that are available when you select User-defined Topology:

  

  The following table shows the type of migration for each mode:

  Mode	Migration Type
  Fixed Topology	End-to-end
  User-defined Topology + Complete Migration	End-to-end
  User-defined Topology + Configuration Migration	Lift-and-shift
  User-defined Topology + Configuration and Edge Migration	Lift-and-shift. Supports HCX for workload migration.

  An end-to-end migration migrates the whole NSX-V environment. A lift-and-shift migration migrates configurations (and the Edges, if you choose the Configuration and Edge Migration mode). For more information, see "Migrating a User-Defined Topology" below.

  Load balancer is supported in a lift-and-shift migration for single-site and cross-VC environments. The NSX-V load balancer will be migrated to an NSX load balancer.

• vSphere Networking

  In this mode, you migrate vSphere Distributed Switch (VDS) 6.5.0 and 6.6.0 to NSX Virtual Distributed Switch (N-VDS). For more information, see Migrating vSphere Networking.

• Aria Automation

  Similar to the "Migrate NSX for vSphere" mode, you can select Fixed Topology or User Defined Topology. Before migrating a user-defined topology, you must check the Aria Automation documentation to ensure that your version of Aria Automation supports the migration of a user-defined topology. For more information about this migration mode, see Migrating NSX-V with Aria Automation - Fixed Topology or Migrating NSX-V with Aria Automation - User-Defined Topology.

The following advanced migration modes are available:

• Edge Cutover

  In this mode, north-south traffic is migrated from NSX-V to NSX. For more information, see Migrating North-South Traffic to NSX Edges Using Edge Cutover.

• Distributed Firewall

  In this mode, you do a lift-and-shift migration of the distributed firewall. For more information, see Migrating Distributed Firewall Configuration.

• Distributed Firewall, Host and Workload

  In this mode, you do an in-place migration of the distributed firewall, hosts, and workload VMs. For more information, see In-Place Migration of Specific Parts of NSX-V.

Note: If ESGs are present in the NSX-V environment, it is recommended that you choose the "Migrate NSX for vSphere" mode (or the "Migrate NSX for vSphere with vRealize Automation" mode if appropriate). This is the optimal way to migrate topologies with ESGs. When you choose the "NSX for vSphere" migration mode, you can still do a lift-and-shift migration if you choose "User-Defined Topology + Configuration Migration" or "User-defined Topology + Configuration and Edge Migration."

Migrating a User-Defined Topology

In the Migrate NSX for vSphere mode, if you choose User Defined Topology, you have the following options:

• Complete Migration - This will migrate everything (configurations, Edge Services Gateways, Distributed Logical Routers, hosts and workloads) in place without the need for additional hosts.
• Configuration Migration - This will migrate configurations only. After the migration, you can create a bridge between NSX-V and NSX, and perform a north-south traffic cutover from NSX-V to NSX. Then you can migrate the workload VMs.
• Configuration and Edge Migration - This will migrate configurations, bridge the NSX-V logical switches to their corresponding NSX segments, and migrate Edge nodes for north-south traffic cutover. You can migrate workload VMs after the Edge nodes are migrated. This mode supports the HCX V2T Migration Workload Mobility capability.

Load balancer is supported for all three options. The NSX-V load balancer will be migrated to an NSX load balancer.

Migrating a Cross-vCenter Environment to NSX Federation

You can migrate an NSX-V cross-vCenter environment to an NSX Federation environment in NSX. You must perform the migration from the Global Manager, choose the Migrate NSX for vSphere mode and select User Defined Topology. If you are running NSX 4.1.0, you can then choose either Complete Migration or Configuration Migration. Starting with NSX 4.1.1, you can also choose Configuration and Edge Migration.