If you have installed NSX on a vSphere Cluster using transport node profiles, you can follow these instructions to uninstall NSX from all hosts in the cluster.

For more information on transport node profiles, see Add a Transport Node Profile.

If you have not used a transport node profile to install NSX, or if you want to remove NSX from a subset of the hosts in the cluster, see Uninstall NSX from a Managed Host in a vSphere Cluster.

Note: Follow these instructions to uninstall NSX from a host in a cluster: Uninstall NSX from a Managed Host in a vSphere Cluster.

Procedure

  1. From a browser, log in with admin privileges to an NSX Manager at https://<nsx-manager-ip-address> or https://<nsx-manager-fqdn>.
  2. Select System > Fabric > Nodes.
  3. From the Managed by drop-down menu, select the vCenter Server.
  4. Select the cluster you want to uninstall, and select Remove NSX.
    Note: If NSX Intelligence is also deployed on the host, uninstallation of NSX will fail because all transport nodes become part of a default network security group. To successfully uninstall NSX, you also need to select the Force Delete option before proceeding with uninstallation.
  5. Verify that the NSX software is removed from the host.
    1. Log into the host's command-line interface as root.
    2. Run this command to check for NSX VIBs 
      esxcli software vib list | grep -E 'nsx|vsipfwlib'
  6. (Host on a VDS 7.0 switch) If the host goes into failed state and NSX VIBs cannot be removed, then run the nsxcli -c del nsx command to remove NSX from the host.
    1. Before running the del nsx command, do the following:
      • If there are VMkernel adapters on NSX port groups on the VDS switch, you must manually migrate or remove vmks from NSX port group to DV port groups on the VDS switch. If there are any vmks available on the NSX port groups, del nsx command execution fails.
      • Put the ESXi host in maintenance mode. The VMware vCenter does not allow the host to be put in maintenance mode unless all running VMs on the host are in powered off state or moved to a different host.
      • Permanently disconnect the ESXi host transport node from NSX Manager by stopping nsx-proxy service running on the ESX host transport node. Log in to the ESXi CLI terminal and run /etc/init.d/nsx-proxy stop.
      • Refresh the NSX Manager UI.
      • Verify that the state of the ESXi host transport node is Disconnected from NSX Manager.
    2. Log in to the ESXi CLI terminal.
    3. Run nsxcli -c del nsx.
    4. Read the warning message. Enter Yes if you want to go ahead with NSX uninstallation. 
      Carefully read the requirements and limitations of this command:
1. Read NSX documentation for 'Remove a Host from NSX or Uninstall NSX Completely'.
2. Deletion of this Transport Node from the NSX UI or API failed, and this is the last resort.
3. If this is an ESXi host:
        a. The host must be in maintenance mode.
        b. All resources attached to NSXPGs must be moved out.
        c. If this is a SmartNIC-enabled host, the host must be rebooted after vib removal is completed. Verify this by checking /var/run/log/esxupdate.log for the thread which shows nsx-lcp component removal and confirm it completed without error. It will look something like:

                In(14) esxupdate[2150621]: Starting runnable component remove -n nsx-lcp-bundle:4.1.1.0.0-8.0.21958016 with 6e3446d0-8393-5869-8873-076a95930f56
                ...
                Db(15) esxupdate[2150621]:  Finished execution of command = component.remove
If the above conditions for ESXi hosts are not met, the command WILL fail.
4. If this is a Linux host:
        a. If KVM is managing VM tenants then shut them down before running this command.
        b. This command should be run from the host console and may fail if run from an SSH client
           or any other network based shell client.
        c. The 'nsxcli -c del nsx' form of this command is not supported
5. If this is a Windows host:
        NOTE: This will completely remove all NSX instances (image and config) from the host.
6. For command progress check /scratch/log/nsxcli.log on ESXi host or /var/log/nsxcli.log on Linux host or 'c:/Programdata/VMware/NSX/Logs/nsxcli.log' on Windows host.
Are you sure you want to remove NSX on this host? (yes/no) yes
      Important: After running the del nsx command, do not use the Resolve functionality in the NSX Manager UI to re-prepare the host that is in Disconnected state . If you use the Resolve functionality, the host might go into Degraded state.
    5. In the NSX Manager UI, if a TNP is attached to the cluster, detach the profile.
    6. Select each host and click Remove NSX.
    7. In the pop-up window, select Force Delete and begin uninstallation.
    8. On the ESXi host, verify that system message displayed is Terminated. This message indicates that NSX is completely removed from the host.
      All existing host switches are removed, transport node is detached from NSX Manager, and NSX VIBs are removed. If any NSX VIBs remain on the host, contact VMware support.