After creating a customer, configure the feature options and settings that the customer can access. As a Partner Super User, you can choose the settings the partner customer can modify.

When you create a new customer, you are redirected to the Customer Configuration page, where you can configure the customer settings.

You can also navigate to the Configuration page from the Manage Customers page in the Partner portal. Select the customer and click Actions > Modify or click the link to the customer.

In the customer or Enterprise portal, click Configure > Customer, and you can configure the following settings.

Customer Capabilities

Only an Operator can activate or deactivate the capabilities. You can view the status of the following capabilities. If you want to activate or deactivate any of the capabilities, contact your Operator.

  • Enable Enterprise Auth
  • Enable Legacy Networks
  • Enable Premium Service
  • Enable Role Customization
  • Enable Segmentation
  • Enable Stateful Firewall.
  • CoS Mapping
  • Service Rate Limiting

Security Policy

When creating Edge-to-Edge IPSec tunnels, you can modify the security policy configuration settings at the Customer Configuration level.

  • Hash - By default, there is no authentication algorithm configured for the VPN header. When you select the Turn off GCM checkbox, you can select one of the following as the authentication algorithm for the VPN header, from the drop-down list:
    • SHA 1
    • SHA 256
    • SHA 384
    • SHA 512
  • Encryption - AES 128-Galois/Counter Mode (GCM), AES 256-GCM, AES 128-Cipher Block Chaining (CBC) and AES 256-CBC are the encryption algorithms modes used to provide confidentiality. Select either AES 128 or AES 256 as the AES algorithms key size to encrypt data. The default encryption algorithm mode is AES 128-GCM, when the Turn off GCM checkbox is not selected.
  • DH Group - Select the Diffie-Hellman (DH) Group algorithm to be used when exchanging a pre-shared key. The DH Group sets the strength of the algorithm in bits. The supported DH Groups are 2, 5, 14, 15, and 16. It is recommended to use DH Group 14.
  • PFS - Select the Perfect Forward Secrecy (PFS) level for additional security. The supported PFS levels are 2, 5, 14, 15, and 16. By default, PFS is deactivated.
  • Turn off GCM - By default, AES 128-GCM is enabled. If required, select the checkbox to turn off this mode, which in turn enables AES 128-CBC mode.
  • IPsec SA Lifetime - Time when Internet Security Protocol (IPSec) rekeying is initiated for Edges. The minimum IPsec life time is 3 minutes and maximum is 480 minutes. The default value is 480 minutes.
  • IKE SA Lifetime - Time when Internet Key Exchange (IKE) rekeying is initiated for Edges. The minimum IKE life time is 10 minutes and maximum is 1440 minutes. The default value is 1440 minutes.
    Note: It is recommended not to configure low life time values for IPsec (less than 10 minutes) and IKE (less than 30 minutes) as it can cause traffic interruption in some deployments due to rekeys. The low life time values can be used only for debugging purposes.
  • Secure Default Route Override – Select the checkbox to ensure that the traffic from the Edge is routed based on the Network Service configured for the Business Policy rule, even when secure routing (either Static Route or BGP Route) is enabled on the Edge.
Note: When you modify the security settings, the changes may cause interruptions to the current services. In addition, these settings may reduce overall throughput and increase the time required for VCMP tunnel setup, which may impact branch to branch dynamic tunnel setup times and recovery from Edge failure in a cluster.

Service Access

Choose the services the customer can access along with the roles and permissions available for the selected service. See Configure Service Access.
Note: If Edge Network Intelligence service is enabled for a customer, ensure not to select the Self Healing checkbox as the Self Healing feature is not completely supported in the 5.0.0 release.

Gateway Pool

The current Gateway pool associated with the selected customer is displayed. If required, you can choose a different Gateway pool from the available list.

If the Gateways available in the Gateway pool have been assigned with Partner Gateway role, you can handoff the Gateways to partners. Select the Enable Partner Handoff to configure the handoff options for the segments and Gateways. For more information, see Configure Partner Handoff.

Maximum Segments

Displays the maximum number of segments configured by the Operator.

OFC Cost Calculation

Displays whether Distributed Cost Calculation is enabled or not by the Operator. By default, the Orchestrator is actively involved in learning the dynamic routes. Edges and Gateways rely on the Orchestrator to calculate initial route preferences and return them to the Edge and Gateway. The Distributed Cost Calculation feature enables to distribute the route cost calculation to the Edges and Gateways.

For more information on Distributed Cost Calculation, refer to the Configure Distributed Cost Calculation section in the VMware SD-WAN Operator Guide available at: https://docs.vmware.com/en/VMware-SD-WAN/index.html.

Note: To enable the Distributed Cost Calculation feature for your customers, contact the support team.

Edge NFV

Displays whether the customers are allowed to deploy third party Virtual Network Functions (VNF) on service ready Edge platforms.

Edge Image Management

Displays the current Software/Firmware Image associated with the selected Partner Customer. As a Partner Super User, you can select and assign a different Software/Firmware Image from the available list of software images for the customer, if needed.

If you want a Partner Customer to manage Edge software images then you have to enable the Delegate Edge Software Image Management checkbox. Once you enable Delegate Edge Software Image Management and click Save Changes, all the assigned software images for the Partner Customer appears. Click Modify to add or remove a software image for the selected customer.
Note: You can remove an assigned image from a Partner Customer only if the image is not a default image and it is not currently used by any edges within the Partner Customer.

For more information, see the Edge Software Image Management section in the VMware SD-WAN Administration Guide available at https://docs.vmware.com/en/VMware-SD-WAN/index.html.

Other Settings

This option is available only when you have the User Agreement feature activated by your Operator. For the selected customer, you can change the user agreement default settings using the following options:

  • User Agreement Display - Select the relevant option from the list to override the default display settings of the User Agreement. By default, the customer inherits the display mode set in the System Properties.
  • User Agreement - Select the user agreement from the list that you want to display for the customer. By default, the customer inherits the default user agreement.

After making changes to the configurations, click Save Changes.