Configuring automatic name resolution

The TM_USEAUTONAME option in the name-resolver.conf file enables you to configure the Name Resolution probe to automatically resolve system names by using the naming sources in the order that you specify.

• “Configuring automatic name resolution” section in Chapter 3, Discovery, in the IP Manager Concepts Guide provides more information on naming-source sequence used by the Name Resolution probe to resolve system names.

• “Configuring automatic name resolution”section in Chapter 3, Discovery, in the IP Manager Concepts Guide provides more information on AutoNameOrder naming sources.

  To configure automatic name resolution:

  1. Go to the BASEDIR/smarts/bin directory in the IP Manager installation area and type the following command to open the name-resolver.conf file:

                          sm_edit conf/discovery/name-resolver.conf
                       

  2. Find the NameFormat section of the file:

     #NameFormat = "TM_USESEEDNAME"
     NameFormat = "TM_USEAUTONAME"
     

  3. Ensure that the NameFormat = “TM_USEAUTONAME” option is the only one that is not commented out.

  4. Find the AutoNameOrder section of the file:

     AutoNameOrder 0 TM_USELOOPBACK
     AutoNameOrder 1 TM_USESYSNAME
     AutoNameOrder 2 TM_USENONPRIVATEIP
     AutoNameOrder 3 TM_USEPRIVATEIP
     AutoNameOrder 4 TM_USEAGENTADDRESS
     

  5. Change the AutoNameOrder numbers (0 through 4) to the order that you prefer. The resolution process is performed in ascending order, starting with AutoNameOrder 0. AutoNameOrder naming sources describes the AutoNameOrder naming sources.

Table 1. AutoNameOrder naming sources

Naming source	Description
TM_USELOOPBACK	Resolve loopback IP address: If a loopback interface IP address can be resolved to a name, that name will be used to name the system. By default, the default loopback interface type number is 24, which represents the “software loopback” interface type. For a discovered system that has multiple loopback addresses, the Name Resolution probe tries to resolve the lowest loopback address first. If that resolution fails, the Name Resolution probe tries to resolve each of the remaining loopback addresses.
TM_USESYSNAME	Resolve MIB-II sysName: If the sysName can be resolved to at least one IP address, and at least one of the resolved IP addresses resolves back to the sysName, the sysName will be used to name the system.
TM_USENONPRIVATEIP	Resolve non-private IP address: If at least one of the IP addresses is not a private IP address, the non-private IP address will be used to resolve the name. Once a name is resolved, the name will be used to name the system.
TM_USEPRIVATEIP	Resolve private IP address: If at least one of the IP addresses is a private IP address, the private IP address will be used to resolve the name. Once a name is resolved, the name will be used to name the system. By default, the private IPv4 address pattern is 10.*|192.168.*|172.<16-31>.*, which is defined as follows: Any IP address with the value of 10 in the first octet (10.*.*.*). Any IP address with a value of 172 in the first octet and a value between 16 and 31 in the second octet (172.<16-31>.*.*). Any IP address with a value of 192 in the first octet and a value of 168 in the second octet (192.168.*.*).
TM_USEAGENTADDRESS	Resolve SNMP agent address: If an SNMP agent address can be resolved to a name, that name will be used to name the system.

1. Save and close the file.

   The modified version of the name-resolver.conf file is saved to the BASEDIR/smarts/local/conf/discovery directory.

2. Type the following command from BASEDIR/smarts/bin to implement your changes:

                  sm_tpmgr -s <
                     IP Manager
                  
                   instance name> -b <
                  brokerName:port
                  >
                  
      --load-conf=name-resolver.conf
                  sm_tpmgr -s INCHARGE-AM -b localhost:426  --load-conf=name-resolver.conf
               

3. Optional: Configure exceptions to automatic name resolution by using a seed file, as described in “Configuring exceptions to automatic name resolution” on page 154.

   If the resolution process is unsuccessful for all naming sources that are defined in the name-resolver.conf file, a final procedure uses a public IP address, a private IP address, or the SNMP agent address for the system name.